Welded copper foil connector ntsa hta n bung ai, n-gun n rawng ai (sh) sharawt tawn da ai jut ni gaw, foil stack hpe n-gun n rawng ai (sh) n bung ai hku n-gun n rawng ai ngu ai lachyum rai nga ai. Manghkang gaw jut langai kaw sha pru wa yang, welding current (sh) temperature hpe n jat shi yang, foil alignment, tooling flatness, bungli galaw ai shara hte buga na n-gun hpe jep yu u.
Mu lu ai hkrang gaw, n-gup magap kata na masa hpe n mai kam ai. Bai galaw ai (sh) n shapraw shi yang, dai daw hpe ginhka nna jep yu u.
N bung ai (sh) sharawt ai Edge gaw hpa hpe madun ai kun?
| N kaja ai hkrang | Shawng nnan jep yu na shara |
|---|---|
| Langai jut (sh) maga mi sha sharawt ai . | Tooling parallelism, bungli galaw ai shara hte buga na n-gun |
| Foil layer law law pru wa ai (sh) shinggrup da ai | Htu hkam sharang lu ai, shinggyin tawn da ai hte maga de na shara |
| Terminal ting gaw hka kaba ai | Katsi ai shang ai, shinggrup ai hte n-gun-shapraw ai aten |
| Ntsa maga gaw n-gup magap rai tim, layers ni garan mat ai | San seng ai lam, interface matut mahkai ai lam, katsi ai hte hkam la ai aten |
| Magri hpe maga mi de sit kau ai | Foil shamu shamawt ai (sh) grai katsi ai hkrang nsam |
| Dai n kaja ai lam gaw, jak langai sha maga de bai kahtap nna byin pru wa ai. | Tooling hpun ai, dip ai alignment (sh) n bung ai dip ai |
N-gun kya ai matut mahkai lam gaw flat terminal kata kaw makoi nga lu ai majaw, hkrang hte hkum hkrang n-gun hpe garan nna jep joi ra na re.
Hpaga galaw ai ladat hpe tup hkrak chye lu na matu, anhte a lam matsun hpe yu u.magri mang n-gun rawng ai busbar garan ai welding galaw ai ladat.
Diffusion welding jak hpe yu u
Copper Foil n-gup magap hpe sharawt ai lam a majaw byin chye ai lam ni
1. N tara ai (sh) n bung ai hku shinggyin tawn da ai magri mang foil ni
Thin copper foil ni gaw, jum ai hte htaw ai shaloi shamu shamawt chye ai. Grau galu ai layer, burr (sh) nga taw sai fold gaw pressure npu hta n-gun yawm mat chye ai.
Foil npawt ni hpe ngang grin ai reference hte shingdaw nna align galaw u. End stops ni gaw bonding galu ai hpe hkang ya nna, side guides ni gaw maga mi de shamu shamawt ai hpe pat shingdang ya ai. Hkum tsup ai terminal ginra gaw, akyu rawng ai tooling matut mahkai ginra kata kaw sha nga ra ai.
Bai nna, buga ginra hta matut mahkai ai lam hpe pat shingdang lu ai particles, sau, oxidation hte hkra machyi ai jut ni hpe mung jep yu u.
2. Hten za mat sai (sh) n -parallel Graphite arung arai
Hten za mat ai graphite, magri n-gun, n-gun n rawng ai jut (sh) n kaja ai hku jung da ai gaw, lapran daw hpe matut mahkai nga ai aten hta, jut langai mi hta gap tawn da ya lu ai.
Ntsa hte lawu graphite block ni hpe n-gun n rawng ai, n-gun n rawng ai hte n bung ai hku n-gun n rawng ai hpe jep yu u. Dai n kaja ai lam gaw, jak a maga mi kaw sha galoi mung pru wa yang, welding galaw ai aten hpe n galai shi yang, tooling, press head hte guides ni hpe jep yu u.
3. N bung ai n-gun garan ai lam
Madun da ai pressure gaw, stack a daw shagu maren mara pressure lu ai hpe sakse n madun ai. Hkrang garan ai lam gaw, n-gun rawng ai shara, tooling alignment hte bungli galaw ai shara hta mung madung nga ai.
Off-centre stack (sh) tilted galaw ai arung arai gaw, jut langai hpe hpaw tawn da ya lu ai. Hka lum ai aten hta stable pressure hpe gawgap da u, dai hku galaw yang, magri n-gun yawm wa ai hte maren, foil ni n htum mat na re.
4. Grai law ai (sh) n bung ai Heat Input
Curled edge ngu ai gaw, grai katsi ai ngu ai lachyum n re. Grai katsi ai gaw, magri hpe n-gun yawm shangun nna, maga mi de shamu shamawt ai lam hpe jat shangun ai; n hkum tsup ai (sh) n bung ai katsi ai gaw, jut langai hpe n shinggrup ai sha tawn da ya lu ai.
Ya aten, katsi ai aten hte katsi ai hpe hkap la ai aten ladaw hte shingdaw yu u, magri grade langai sha, foil n-gun, layer jahpan hte terminal area ni a matu.
5. Terminal n shim lum shi yang, Pressure hpe shapraw kau ai
Terminal gaw katsi nna n-gun n rawng ai sha, tooling hpaw mat yang, foil jut gaw bai nhtang pru wa chye ai (sh) garan mat chye ai.
Validated hold aten laman hta pressure hpe matut manoi galaw u. Hpang na daw ni n bung mat yang, tool temperature, katsi ai hte galaw shapraw ai aten hpe jep yu u.
Parameters n galai shi yang, hpa majaw byin ai hpe gara hku tam na?
1. Cold-Press Test galaw na
N-gun n rawng ai sha, dat kasa stack hpe dip u. Wrinkling (sh) shift galaw ai shara ni hpe htu ai, shinggrup ai, shara (sh) n-gun jaw ai lam ni hpe galaw ai. Cold pressing gaw ngang grin ai rai yang, katsi ai garan ginhka ai lam hte katsi ai hpe hkam la ai ladat hpe jep yu u.
2. Bungli galaw ai shara hpe 180 Degrees shinggrup u .
Machine setup hpe n galai shai ai sha, bungli galaw ai arai hpe shinggrup ngut ai hpang, bai chyam yu u.
Dai n kaja ai lam gaw, jak maga mi kaw sha naw nga yang, graphite block ni hpe jep yu nna, press baw hte buga na n-gun hpe dip yu u.
Dai n kaja ai lam gaw bungli galaw ai shara langai sha a jut kaw hkan nang ai rai yang, foil hpe gang je kau ai, shinggyin tawn da ai hte shinggyin tawn da ai hpe jep yu u.
3. Pressure matut mahkai ai lam hpe jep yu u .
Hkum tsup ai terminal ting hta pressure matut mahkai ai lam hpe jep yu u. Rawt ai jut makau na nhtoi (sh) n lawm ai masat kumla gaw n bung ai hku shinggrup ai lam hpe madun ai.
Graphite block ni hpe shanhte jung da ai shara kaw yu yu ga. Block langai hpe shaw kau ngut ai hpang flat zawn rai tim, ngam ai, n jaw ai madi shadaw ai lam (sh) installation error a majaw angle langai kaw dung nga ai.
4. Parameter langai hpe langai lang galai kau u .
Shawng shara, tooling hte pressure hpe hkrak hkra galaw u. Dai hpang, kaja ai galai shai ai lam hpe chye na lu na matu, hkang zing da ai lahkam ni hku nna, current, heating time (sh) hold time hpe gram lajang u.
N bung ai magri mang n-gang n-gang htum ni a matu sharai la ai lam ni
| Jep joi mahtai | Shading sharai ai lam |
|---|---|
| Foils ni gaw kaja ai matut mahkai shara shinggan de jat wa ai | Stack hpe bai shara jahkrat u (sh) n-gun rawng ai shara hpe ka-up da ai tooling hpe lang u. |
| Layer langai hkrai hpe offset galaw da ai | Hpang jahtum na hkring ai shara ni hte maga de na lam matsun ni hpe jat bang u; daw ai hpe hkang ai lam hpe grau kaja hkra galaw u |
| Foil ni gaw shinggrup ai shaloi shamu shamawt ai | Hkrun lam madi shadaw ai lam hpe grau kaja hkra galaw nna, n-gun n rawng shi yang, n-gun hpring hpring hpe gawgap u |
| Graphite ntsa gaw n-gun yawm mat ai (sh) awu asin rai mat sai | Graphite block hpe gingdan ai hku jasan jaseng, bai gram lajang (sh) galai kau u . |
| Lawu na hte lawu na tooling ni gaw n bung ai . | Hpaji hkingrai ni hpe sharai la u, baw hpe dip u (sh) lam madun ai hkrang hpe dip u |
| Langai maga de gaw n-gun kya ai matut mahkai lam nga ai | Bungli galaw ai arai hpe lapran de tawn da nna matut mahkai ai lam hpe jep yu u |
| Copper hpe grai n-gun ja hkra galaw ai (sh) maga mi de sit kau ai | Pressure hte shara hpe sharai la ngut ai hpang, hkang lu ai lahkam ni hta katsi ai hpe shayawm kau u |
| Edge gaw grai n hkrat sum ai sha n matut mahkai nga ai | San seng ai lam hte n-gun hpe jep yu u, dai hpang katsi ai hpe jep joi yu nna hkam la ai aten |
| N-gun dat ngut ai hpang Terminal hpaw ai | Tengman ai post-katsi ai aten hpe jat ya u |
Ga shadawn: Copper Foil Connector a jut langai kaw n-gup magap hpe sharawt ai
Ndai laika hta madun da ai sample hta, magri mang n-gang law law gaw jut langai kaw sharawt nna shinggrup mat ai shaloi, welded terminal law malawng gaw n-gun n rawng ai sha naw nga nga ai.
Hpa majaw nga yang, n kaja ai lam gaw maga mi de sha madung tawn ai majaw, shawng nnan e, tooling parallelism, bungli galaw ai shara, foil alignment hte local pressure hpe jep yu u. Current grau law ai gaw, buga gap hpe n pat ai sha, katsi ai hpe jat ya lu ai.
Hpaji jaw da ai ladat gaw:
- Ntsa hte lawu na graphite block ni hpe jep yu nna jasan jaseng u.
- Terminal ginra ting hpe madi shadaw ya ai hpe kam u.
- Cold-press test galaw nna foil shamu shamawt ai hpe yu u.
- Bungli galaw ai shara hpe shinggrup nna, bai chyam yu u.
- Pressure-matut mahkai ai lam hpe yu yu ga.
- Katsi ai hpe n gram shi yang, jak a masa hpe sharai la u.
- Hpang jahtum na joint hpe ra ai dimensional, wan (sh) jak rung chyam dinglik ai lam hpe lang nna jep yu u.
Sumla gaw ndai sequence hpe tsun dan ai; hpa majaw byin ai hpe sample, tooling hte machine ntsa kaw nna jep yu ra ai.
N bung ai Magri Foil Connector hpe bai galaw mai ai kun?
Lajang da ai trimming allowance kata na arung arai ni hpe ngam ai bond hpe jep yu ngut ai hpang trim galaw mai ai. Dai n kaja ai lam gaw ngut sai terminal de shang wa nna, layers ni hpe dan dawng shangun ai (sh) matut mahkai shara hpe shayawm kau ai rai yang, dai hpe flat dip dat yang, joint hpe n mai gram lajang ai.
Foil hpe flat hte hkum gap (sh) myit hkrum da ai ladat n nga ai sha bai hkum katsi. Hkrang hpe bai galaw na (sh) ningdang kau na hpe dawdan nna ra ai ninghkap ai lam, n-gun, nsam, shadawn shadang (sh) cross-section jep joi ai lam ni hpe galaw na.
Mu lu ai n-gup magap deformation hta grau nna makoi da ai layer hpe garan ginhka ai lam a matu, anhte a lam matsun hpe hti yu u.magri mang n-gun yawm mat nna, n-gun kya ai matut mahkai lam.
FAQ
San: Hpa majaw magri mang n-gang langai a maga mi sha rawt wa ai kun?
A: Langai -maga mi de n kaja ai lam gaw, bungli galaw ai arung arai n hkrak ai, n -parallel tooling galaw ai, buga na n-gun yawm mat ai (sh) kaja ai matut mahkai shara shinggan de foil jat wa ai hpe madun dan ai.
Q: N-gup magap n-gun yawm mat ai shaloi, welding current hpe shayawm ra ai kun?
A: Tinang hkrai n re. Grai katsi ai gaw karum ya lu ai, raitim n bung ai n-gun, foil shamu shamawt ai hte tooling matut mahkai ai lam ni gaw dai hte bung ai hkrang hpe shabyin ya lu ai. Mechanical setup hpe shawng yu yu ga.
San: Rawt tawn da ai magri foil jut hpe bai flat dip mai ai kun?
A: Flat hku dip dat yang, shi a hkrang hpe grau kaja hkra galaw ya lu ai, raitim, n-gun n rawng ai interface hpe gaw n gram lajang ya lu ai. Terminal hpe bai galaw na matu n hkap la shi yang, jep yu ra ai.
San: Matut manoi galaw shapraw ai hta edge lifting hpe gara hku pat shingdang mai na kun?
A: Foil hpe bai nhtang htu nna shinggrup da ai, shara jahkrat da ai, graphite tooling hpe n-gun n rawng ai, n-gun n rawng ai hte n shapraw shi yang, n-gun rawng ai aten hpe lang u. Katsi ai masa hte galaw shapraw ai aten ladaw ni mung n galai shai ai sha nga ra ai.
HAIFEI hpe matut mahkai mai ai
